Digitalinx (DL-HDE100) HDMI Over HDBaseT 100m Complete Extender Set

In stock

Image result for digitalinx logo

Digitalinx (DL-HDE100) HDMI Over HDBaseT 100m complete extender Set with flexible power, RS232 & IR control, and ethernet

he DigitaLinx DL-HDE100 extender set transmits HDMI (1080p, 4Kx2K (UHD) & 3D) including HDCP 2.2, Ethernet, bidirectional IR, and RS232 up to 100 meters away using a single twisted pair cable.

Built-in surge protection and diagnostic LEDs ensure hassle-free and robust installations. Flexible power design allows the units to be powered at either the TX or RX end, and only one power supply is required. The 12 volt power supply is secured with a screw-on connector to prevent the power from being accidentally disconnected.

The DL-HDE100 is sold only as a set. All accessories are included including two IR emitters, two IR receivers, and two pairs of mounting brackets with screws. The individual transmitter and receiver are not compatible with other HDBaseT devices due to proprietary PoE circuitry.

eatures & Benefits

  • HDMI transmission up to 330 feet (100m)
  • 1080p, 4Kx2K (UHD) & 3D compatible
  • CEC supported
  • Built-in surge protection
  • Diagnostic LEDs
  • HDCP 2.2 compliant
  • Bidirectional Wideband IR and RS232 pass-through
  • 100-BaseT Ethernet pass-through
  • Flexible power design (use power supply at TX or RX)
  • Locking power connector (power supply included)


  • Uses any Cat6 or greater twisted pair cabling
  • Extension of HDMI and control signals
  • Limited access to power for extenders on both ends
  • Ideal for Digital Signage, Home Theater, Commercial Video
Product Line:  DL-HDE100
I/O Connections
HDMI One (1) HDMI Type A Receptacle
Twisted Pair One (1) 8P8C port (Shielded RJ45)
Ethernet One (1) 8P8C port (Shielded RJ45)
IR Input One (1) 3.5 mm TRS Jack
IR Output One (1) 3.5 mm TS Jack
RS232 One (1) 3-Pole Euroblock connector
18V DC Power One (1) 5.5 mm Outside Diameter, 2.1 mm Inside Diameter Barrel (Locking)
Supported Audio, Video and Control
Maximum Video Compatibility 100 m: Deep Color 48/36/30/24 Bit at 1080p, 3D, and 4k x 2k (UHD) up to 30 Hz: RGB, YCbCr 4:4:4, YCbCr 4:2:2; up to 60 Hz: YCbCr 4:2:0
Video Compliance HDMI, HDCP 2.2, and CEC (Consumer Electronics Control)
Embedded Audio Up to PCM 8 channel, Dolby Digital TrueHD, and DTS-HD Master Audio
Input DDC Signal 5.0 volts p-p (TTL)
Input Video Signal 0.5 to 1.0 volts p-p
Maximum HDMI Distance 5 m (pre-made cable)
IR Carrier Frequency Range 33-55kHz at 5 volts
Ethernet 100BaseT
RS232 Baud Rate Up to 115200 baud
HDBaseT Signal Characteristics
Maximum Distance 100 m
Cable Requirements Solid core shielded Category 5e, Category 6 or greater with TIA/EIA-568B crimp pattern
Bandwidth 10.2 Gbps
Gain 0 dB – 10 dB at 100 MHz
Resolution Range 800x600 – 1920x1200
Signal to Noise Ratio (SNR) > 70 dB at 100 MHz over 100 m
Return Loss < -30 dB at 5 KHz
Total Harmonic Distortion (THD) < 0.005% at 1 KHz
Min-Max Signal Level < 0.3 V – 1.45 Vp-p
Differential Phase Error ±10° at 135 MHz over 100 m
Chassis and Environmental
Enclosure Painted steel
Dimensions 135 mm x 74 mm x 15 mm (5.31 in x 2.91 in x 0.59 in)
Shipping Weight 0.82 kg (1.8 lbs)
Operating Temperature (Environment) 0° to +40° C (+32° to +104° F)
Operating Temperature (Chassis) 31° C (88° F) (S); 38° C (100° F) (R)
Operating Humidity (Environment) 20% to 90%, Non-condensing
Storage Temperature (Environment) -10° to +60° C (+14° to +140° F)
Storage Humidity (Environment) 20% to 90%, Non-condensing
Power, ESD, and Regulatory
Maximum Power Consumption 3 watts (S), 6 watts (R)
Power Supply 18V DC
ESD Protection 15kV
Regulatory CE, RoHS
Standard Warranty 2 Years
Diagnostic Indicators Power, Status, Link, and HDCP LEDs
Included Items Installation Guide, power supply, US Power cord, IR emitters (2 ea), IR receivers (2 ea), mounting “L” brackets (4 ea), mounting screws (4 ea)
Write Your Own Review
You're reviewing:Digitalinx (DL-HDE100) HDMI Over HDBaseT 100m Complete Extender Set
Your Rating